Control Unit

Control Unit
FEM-1CP (GREEN FRONT PANEL)

The Sensing Head and Exclusive Single Axis Controller for standard

use, single START input will rotate the Sensing Needle FWD, after

the tool has been detected.

An Ok signal is given, the Needle reverses

and returns to HOME position automatically. If the Needle cannot contact

the tool at specified angle a NG signal is given and it continues FWD to

the END of TRAVEL and returns to HOME position automatically.

FEM-1CP/T (RED FRONT PANEL)

The Sensing Head and Exclusive Single Axis Controller, has the

same operating principle as the FEM-1CP, START input gives detection

direction (FWD input F) and HOME direction (REVERSE input R) uses a

separate input, Detection is the same as FEM-1CP (FWD input F, Terminal #3 F,

REVERSE input R and Terminal #4 R)

FEM-1CP/W (ORANGE FRONT PANEL)

The Sensing Head and Exclusive Single Axis Controller for

Automatic Lathe applications is for work piece detection

exclusively (not tool detection).START input is the same as

FEM-1CP except when a work piece is detected at the specified

angle a NG signal is given. If the Needle continues to the END of TRAVEL

it will give an OK signal! (FEM-1CP OK output and NG will be

Inverted)

Specifications for Broken Tool Sensing Device

Control Unit : FEM-1 CP (Single Axis Control Unit standard usage)

: FEM-1 CP /T (Single Axis Control Unit, start, fwd, Rev, or a separate input)

: FEM-1 CP/W (Single Axis Control Unit, automatic work piece detector)

Sensing Head : 5 Types…..45S, 60S, 90S, 120S & 180S (Cycle e ndurance: 1,000,000 operations)

Voltage : FEM-1CP 24V AC/DC (+ 10%) 150mA

Start Input : 24V DC 11mA per axis

Output(OK NG POS): Universal for NPN and PNP Applications. FET Normality open output 24V DC 150 mA maximum

Safety System : Built in Control Unit Self Monitor

Sensing Time : 45S=0.44sec. 60S =0.45sec. 90S=0.51sec. 120S=0.6sec. 180S=0.62sec.

Rotating Direction : Clockwise (CW) Counterclockwise (CCW) DIP S/W Switching system

Reset Function : A reset B reset DIP S/W switching system

Sensing Needle : 105mm length, 1.2mm dia. and 155mm length, 1.2mm dia.

Sensing Plate : 105mm length, 0.4mm thickness, 5.0mm wide and 155mm length, 0.4mm thickness, 5mm wide.

Waterproof

Corrosion resistant : Sensing Head ISO IP67 chrome plated

Cable : Oil proof cable. 5 meters (standard), can be extended to 20 meters connector 5 meter std. Straight

type no connection required L type use connector long cable 10 meters

LED Light : Power……Yellow

: OK……….Green (detected tool OK)

: NG……….Red (no touch)

: POS……..2nd green (a return to HOME position)

Numbers of

Terminals : FEM-1CP………12 terminals

Control Unit : UL standard

Room Temperature : –10 deg. C~+60 deg. C for Sensing Head (above freezing)

0 deg. C~+50 deg. C for Control Unit (above freezing)

Room Humidity : 35% ~ 85% RH for Control Unit (moisture free)

*Single Controller is universal for NPN and PNP applications.

CAUTION: A protection diode must be used when using a relay on the output socket.

$612.50
SKU:
CP
Weight:
3.00 Ounces
Shipping:
Calculated at Checkout
Adding to cart… The item has been added
    FEM-1CP (GREEN FRONT PANEL)

    The Sensing Head and Exclusive Single Axis Controller for standard

    use, single START input will rotate the Sensing Needle FWD, after

    the tool has been detected.

    An Ok signal is given, the Needle reverses

    and returns to HOME position automatically. If the Needle cannot contact

    the tool at specified angle a NG signal is given and it continues FWD to

    the END of TRAVEL and returns to HOME position automatically.

    FEM-1CP/T (RED FRONT PANEL)

    The Sensing Head and Exclusive Single Axis Controller, has the

    same operating principle as the FEM-1CP, START input gives detection

    direction (FWD input F) and HOME direction (REVERSE input R) uses a

    separate input, Detection is the same as FEM-1CP (FWD input F, Terminal #3 F,

    REVERSE input R and Terminal #4 R)

    FEM-1CP/W (ORANGE FRONT PANEL)

    The Sensing Head and Exclusive Single Axis Controller for

    Automatic Lathe applications is for work piece detection

    exclusively (not tool detection).START input is the same as

    FEM-1CP except when a work piece is detected at the specified

    angle a NG signal is given. If the Needle continues to the END of TRAVEL

    it will give an OK signal! (FEM-1CP OK output and NG will be

    Inverted)

    Specifications for Broken Tool Sensing Device

    Control Unit : FEM-1 CP (Single Axis Control Unit standard usage)

    : FEM-1 CP /T (Single Axis Control Unit, start, fwd, Rev, or a separate input)

    : FEM-1 CP/W (Single Axis Control Unit, automatic work piece detector)

    Sensing Head : 5 Types…..45S, 60S, 90S, 120S & 180S (Cycle e ndurance: 1,000,000 operations)

    Voltage : FEM-1CP 24V AC/DC (+ 10%) 150mA

    Start Input : 24V DC 11mA per axis

    Output(OK NG POS): Universal for NPN and PNP Applications. FET Normality open output 24V DC 150 mA maximum

    Safety System : Built in Control Unit Self Monitor

    Sensing Time : 45S=0.44sec. 60S =0.45sec. 90S=0.51sec. 120S=0.6sec. 180S=0.62sec.

    Rotating Direction : Clockwise (CW) Counterclockwise (CCW) DIP S/W Switching system

    Reset Function : A reset B reset DIP S/W switching system

    Sensing Needle : 105mm length, 1.2mm dia. and 155mm length, 1.2mm dia.

    Sensing Plate : 105mm length, 0.4mm thickness, 5.0mm wide and 155mm length, 0.4mm thickness, 5mm wide.

    Waterproof

    Corrosion resistant : Sensing Head ISO IP67 chrome plated

    Cable : Oil proof cable. 5 meters (standard), can be extended to 20 meters connector 5 meter std. Straight

    type no connection required L type use connector long cable 10 meters

    LED Light : Power……Yellow

    : OK……….Green (detected tool OK)

    : NG……….Red (no touch)

    : POS……..2nd green (a return to HOME position)

    Numbers of

    Terminals : FEM-1CP………12 terminals

    Control Unit : UL standard

    Room Temperature : –10 deg. C~+60 deg. C for Sensing Head (above freezing)

    0 deg. C~+50 deg. C for Control Unit (above freezing)

    Room Humidity : 35% ~ 85% RH for Control Unit (moisture free)

    *Single Controller is universal for NPN and PNP applications.

    CAUTION: A protection diode must be used when using a relay on the output socket.

    Write a Review

Similar Products

Also Viewed